Parts & Accessories
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 14.8mm - Length: 10.6mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Shimano HB-C201 Front - 105 HB-1050 Front - Deore LX/Mtn LX Front - STX HB-MC32/30 Front - Shimano HB-A410, HB-A416 Front
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 10mm x 26, rear hub - Compatible with 10mm x 26 axle - Cone Wrench Size: 15mm - Threads: 10mm x 26 - Diameter: 17.0mm - Length: 13.8mm - Note: O-ring / seal not included. - 1 cone per bag COMPATIBLE HUBS: - JoyTech 10mm x 26, rear hub - Taiwanese hubs with 10mm x 26 axle
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.7mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Ultegra 6400 Front - Shimano 105 HB-5500 Front - Shimano 105 HB-5501 Front - 105 SC 6400 Front
$1.30 - $5.95
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
$11.49 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Salsa springs for Flip-Off skewers
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
On today's MTB frames, there are many diameters and width dropouts standards. Most Mavic wheels can be fitted with specific adapters to match with those frames: 142mm extenders for ITS-4 hubs, 142 mm extenders for TS-2 hubs and QR adapters (delivered with a front quick release) for all of them. - Converts a 12mm rear axle to fit in a frame with 9.5mm dropouts - Requires one pair per hub
Page 1 of 1