Wheels

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - Crafted from lightweight aluminum - End Cap Sold Separately - Weight: 39 g

Stainless spoke nipple flat washers from Whisky. - Bag of 34 Washers

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

- ProLock: pre-prepped/treated nipple threads with special compound - Hexhead (14g only) design for building/truing at nipple head, in addition to 4-sided flats at rim protrusion - Form-A design assures smooth fit and build - Cold-forged nipple blank machined to DIN 79012 specs - 14mm overall length (2mm taller hexhead for wrench interface, but protrusion through rim is the same as a 12mm DT nipple) - 2.0mm (14g) spoke thread interface with full run-through - Made in Switzerland. - Box/100

- Straight gauge 2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads - 222g @ 32h/265mm - Box of 100 - Nipples sold separately

Champion 2.0 Black Spokes - One 264mm spoke = 7g

Make it more aerodynamic – this nipple is hidden inside the rim. DT Hidden Nipples are designed for high-profile rims, in which the inverted design is essential for optimum precision. They are very light and hidden on the inside of the rim: perfectly suited for high aero wheels. The nipples will align perfectly due to their spherical contact surface. - Weight: 22g for 64 nipples

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - One 264mm spoke = 6g - Nipples sold separately

- Straight gauge 2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads. Black surface treatment resists scratches - 222g @ 32h/265mm - Box of 72 - Nipples sold separately

Competition Black Spokes for wheel service and repairs. - Double Butted: 2.0/1.8/2.0 - Box of 100 Spokes - One 264mm spoke = 6g - Nipples sold separately

- Double butted 2.0/1.5/2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads - 143g @ 32/265mm - Box of 72 - Nipples sold separately

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

- Double butted 2.0/1.5/2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads. Black surface treatment resists scratches - 143g @ 32/265mm - Box of 72 - Nipples sold separately

- Bladed Revolution spokes 2.0/.09x2.3/2.0mm, black surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 139g (32/265mm) - Box of 20 - Nipples sold separately

- Bladed Revolution spokes 2.0/.09x2.3/2.0mm, black surface treatment resists scratches - Cold forging technology, CrNi stainless steel with rolled threads - No hub slotting necessary - 139g (32/265mm) - Box of 20 - Nipples sold separately

Salsa springs for Flip-Off skewers

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Grade 10 chromium steel balls MR17287LLB - 17 x 28 x 7mm 6808LLB - 30 x 42 x 7mm

Adapters for converting rear wheel compatibility. Check the wheel page on mavic.com (specification section) to make sure you order the right adapter. 

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 10mm x 26, rear hub - Compatible with 10mm x 26 axle - Cone Wrench Size: 15mm - Threads: 10mm x 26 - Diameter: 17.0mm - Length: 13.8mm - Note: O-ring / seal not included. - 1 cone per bag COMPATIBLE HUBS: - JoyTech 10mm x 26, rear hub - Taiwanese hubs with 10mm x 26 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 14.8mm - Length: 10.6mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Shimano HB-C201 Front - 105 HB-1050 Front - Deore LX/Mtn LX Front - STX HB-MC32/30 Front - Shimano HB-A410, HB-A416 Front

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.7mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Ultegra 6400 Front - Shimano 105 HB-5500 Front - Shimano 105 HB-5501 Front - 105 SC 6400 Front

Dynaplug tubeless tire repair plugs are constructed from viscoelastic rubber impregnated cord. The plugs are specially designed to be inserted directly into a puncture after object has been removed. - Combo pack includes x5 replacement plugs: x3 pointed brass soft nose tip plugs x2 Megaplugs - Made in USA - The Megaplugs are compatible with: Megapill tool, Megaplugger tool, and the Racer series of tools - The brass soft nose tip are compatible with all Dynaplug tools, except for Air Road tool NOTE: for Air Road plugs, please use part # 380-2020

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.